Mesa Electronics

Freight fee required for RMA's boards returned with no problem found, or miscellaneous shipments required, captured per fees intended. Please enter RMA number or any other requirements in the 'Customer Comment' field.

RMA21654 Repaired Card 7I77U S/N: ms5925306: Damage, Over voltage, Replaced diode 5VTVS in location CR8 | Repair fee: $35.00 Freight fee: $ 21.95 Total $ 56.95 RMA BOARD REPAIR PLUS FREIGHT | Requirements are: Before returning any board(s) for any reason a RMA number must be assigned. Request by ema

The THCAD is a frequency to voltage converter type A-D designed for high noise environments like plasma voltage monitoring for torch height controls. The THCAD is available in three voltage ranges, 0-5V, 0-10V and 0-300V. When used for plasma voltage monitoring, the 5V and 10V versions require an ex

The 7I94 is a Ethernet connected motion control interface designed for interfacing up to eight high speed RS-422 or RS-485 serial devices including Mesa sserial remote interfaces, absolute encoders and general serial interfacing. In addition, a FPGA expansion connector compatible with Mesa's 25 pin

The 7I76ED ia a remote FPGA card with Ethernet interface designed for interfacing up to 5 Axis of step &dir step motor or servo motor drives and also provides a spindle encoder interface, isolated analog spindle speed control and 48 isolated I/O points for general purpose field I/O use. All step and

50 conductor flat cable for Anything I/O cards. 5 foot length

50 conductor flat cable for Anything I/O cards. 4 foot length

50 conductor flat cable for Anything I/O cards. 2 foot length

50 conductor flat cable for Anything I/O cards. 3 foot length

50 conductor flat cable for Anything I/O cards. 1 foot length

DB25M to IDC26 flat cable 18 inch Expansion connector cable for 5I25, 5I25T, 6I25,7I76E,7I76EU,7I92TF,7I92TM,7I92TH,7I95,7I95T,7I96,7I96S,7I97,7I97T,7I98,7C80,7C81 FPGA card 26 pin Header to Mesa daughtercards or parallel port breakouts with DB25F connector

The 7I49HV is a 6 channel resolver interface with 6 additional +-10V analog outputs. The 7I49 is intended for applications that read standalone resolvers, as the 7I49 generates the resolver reference excitation. The 7I49HV can be used with 1:1 and 1:2 transformation ratio resolvers. The 7I49HV has a

The CFADPTCS adapters allow use of Compact flash memory cards with any CPU with a 44 pin 2mm or 40 pin .1" IDE connector. The adapters have an activity light and a push button ejector, making it suitable for panel mounting. The CFADPT adapters can be jumpered for master or slave and can get the CF p

The 7I34-LVDS is a 8 channel LVDS interface for Mesa's Anything I/O series of FPGA interface cards. The 7I34-LVDS has 8 independent receive and transmit channels. Each transmit channel has a independent drive enable for bus or 2 wire half duplex systems. The controller connection is a 50 pin header

The 7I96 is a Ethernet connected motion control interface designed for interfacing up to 5 Axis of step&dir step motor or servo motor drives. Step rates up to 10 MHz are supported. The 7I96 also has 11 isolated inputs plus 6 isolated outputs for general purpose I/O use. A high speed encoder interfac

The 7I54 is a low cost 6 Axis H-bridge card for use with Mesa motion control cards. The 7I54 has a maximum per axis current rating of 3 Amps and a voltage rating of 40V. Current limits of 1 Amp and 3 Amp are user selectable, as are voltage and current (torque) modes. All motor power circuitry is gal

Phoenix compatible 3.5 mm 4 position screw terminal block, side entry.

CAT5E cable for SSERIAL/Ethernet 1 foot RJ45 both ends for 7I44/7I74 / Ethernet

The MESA 6I24 is a low cost, general purpose, Xilinx XC6SLX16-2FTG256C FPGA based progr ammable I/O card for the PCIE bus. The 6I24 is a low profile one lane PCIE card (available with low profile and standard brackets, low profile b r acket shown here) Firmware modules are provided for hardware step

The MESA 6I24-25 is a low cost, general purpose, Xilinx XC6SLX25-2FTG256C FPGA based progr ammable I/O card for the PCIE bus. The 6I24 is a low profile one lane PCIE card (available with low profile and standard brackets, low profile b r acket shown here) Firmware modules are provided for hardware s

The 104-AT is a simple PC/104 to ISA adapter to allow using a PC/104 card in a ISA backplane for development purposes.