Mesa Electronics

The 7I34 is a 8 channel RS-422/RS-485 interface for Mesa's Anything I/O series of FPGA interface cards. The 7I34 has 8 independent receive and transmit channels. Each transmit channel has a independent drive enable for bus or 2 wire half duplex systems. The controller connection is a 50 pin header t

Freight fee required for RMA's boards returned RMA21658

FREIGHT ONLY : For order 21651, Ed Ackfeld

The 7I77U is daughtercard/breakout board for use with MESA's 25 pin I/O FPGA cards like the 6I25, 7I92TM or 7I96. The 7I77U is designed for interfacing up to 6 Axis of analog servo motor drives and also provides 48 isolated I/O points for general purpose field I/O use. Six +-10V analog outputs and s

7I85S-5I25T PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

7I85-5I25T PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

The 4I27 is a low cost, LM629 based 2 axis DC servo motor control system implemented on a stackable PC/104 bus card. The 4I27 is designed for high performance positioning systems using DC servo motors with quadrature shaft encoders. The per axis output of the 4I27 is an 8 bit sign-magnitude PWM sign

All wire transfers require a $35.00 processing fee.

7I78-5I25T PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

The 7I37 F is an 8 output, 16 input isolated I/O card. The 7I37TA provides 8 Isolated 48VDC 1A output drivers. All output drivers are low saturation voltage MOSFETS for low power dissipation. Each of the 8 output switches is isolated from the others, allowing high side, low side, push-pull and other

7I76U-5I25T PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

7I76-6I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

The 7I84U is a remote isolated 32 input and 16 output digital I/O card. The 7I84U is identical to the 7I84 except that it has universal sourcing/sinking/push-pull outputs. The 16 outputs are rated 5VDC to 28VDC with 500 mA maximum current capability. Outputs have per output short circuit protection,

The 4I71 is a stackable PC/104-plus card that combines a 100BaseT Ethernet MAC with a 8 port switch. The 4I71 makes it easy to connect multiple embedded system cards without the awkward power or mechanical problems with consumer type Ethernet switches. The 8 Ethernet ports support autonegotiation al

The 7I76U is daughtercard/breakout board for use with MESA's 25 pin I/O FPGA cards like the 5I25T,6I25 and 7I92T. The 7I76U is designed for interfacing up to 5 Axis of step & dir step motor or servo motor drives and also provides a spindle encoder interface, isolated analog spindle speed control and

The MESA 3X20 is a high I/O density external PCIE FPGA card. The 3X20 has 144 user I/O available on a tiny 2.5" x 3.25" card. The 3X20 connects to the host via a standard 1 lane PCIE cable or through its motherboard connector. All core and I/O power is regulated on card so only single external 3.3V

7I77U-5I25T PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

BRACKETS - LP (LOW PROFILE) FOR 5I24 OR 6I24

BRACKETS - SP (STANDARD PROFILE) FOR 5I24 OR 6I24

RMA21646 CARD REPAIR PLUS FREIGHT RMA21646 - Repair fee $35. plus $108. Freight fee: TOTAL $143.00 1. 7i76E MS586356 Fault: I cannot control the spindle speed any more. No warranty, repaired at $35. due to corrosion. 2. THCAD - 10 MS5877798 Fault: No frequency output, physical damage on the pc board

Set of 3x 1M Ohm 0.4W 0.1% Resistors for THCAD range extension and direct connection to plasma voltage. Full scale ranges with THCAD-10 or THCAD2 at 10V range: 1 = 110V FS 2 in series = 210V FS 3 in series = 310V FS One set (3 resistors) needed for range extension of one THCAD