Show All LinuxCNC Supported Boards

7I92TM Anything I/O Ethernet card 1x DB25 Male, 1x 26 pin header

The MESA 7I92TM is a low cost, general purpose, FPGA based programmable I/O card with 100 BaseT Ethernet host connection. The 7I92T series replaces the 7I92 series cards. Enhanced features include a larger FPGA, better Ethernet ESD protection, and a pullup/pull down option for the I/O pins. The 7I92

133.90 €

7I96S STEP/IO Step & dir plus I/O with analog spindle card

The 7I96S is a Ethernet connected motion control interface designed for interfacing up to 5 Axis of step&dir step motor or servo motor drives. Step rates up to 10 MHz are supported. The 7I96S also has 11 isolated inputs plus 6 isolated outputs for general purpose I/O use. A high speed encoder interf

183.02 €

7I34 Eight Channel RS-422 interface

The 7I34 is a 8 channel RS-422 interface for Mesa's Anything I/O series of FPGA interface cards. The 7I34 has 8 independent receive and transmit channels. Each transmit channel has a independent drive enable for bus or 2 wire half duplex systems. The controller connection is a 50 pin header that mat

72.48 €

7I36 Quad Analog servo interface

The 7I36 is a 4 axis analog servo interfaces intended for operation with MESA's Anything I/O cards when used for motion control applications. The 7I36 takes offset PWM signals from the Anything I/O card and converts them to +- 10V analog output voltages for direct connection to analog input servo am

183.02 €

THCAD2 High isolation A-D accessory

The THCAD2 is a frequency to voltage converter type A-D designed for high noise environments like plasma voltage monitoring for torch height controls. The THCAD2 has 2 settable input ranges, 5V full scale and 10V full scale to accommodate different plasma source dividers. When used for direct plasma

97.04 €

7I64 Isolated remote I/O card (Obsolete replaced with 7IA0)

The 7I64 is an 24 output, 24 input isolated I/O card. The 7I64 provides 24 isolated 48VDC 2.5A output drivers. All output drivers are low saturation voltage MOSFETS for low power dissipation. Each of the 24 output switches is isolated from the others, allowing high side, low side, push-pull and othe

243.23 €

7I88 16 channel differential output card

The 7I88 is a 16 channel differential driver that can provide up to 8 differential Step/Dir or 8 PWM/Dir output channels. The last channel pair can be be used as a RS-422/RS-485 interface if desired. All differential outputs have a full 5V swing and can be used single ended if required. 5V and GND c

97.04 €

7I68-FON 3X2X cabled PCIE motherboard

The MESA 7I68 is a simple motherboard for 3X2X series FPGA daughtercards. The 7I68 provides a base and simplified I/O connections for the 3X2X series daughtercards. The 7I68 can be used for evaluation of 3X2X series cards or for final application. The 7I68 buffers all I/O pins with quickwitches for

121.62 €

7C80 RPI interfaced Step&dir plus I/O interface

The MESA 7C80 is motion oriented FPGA motherboard host for a Raspberry Pi CPU. The 7C80 connects to the GPIO interface and uses SPI for FPGA communication . The 7C80 provides 5V power for the RPI via a built in switching regulator. The 7C80 has 6 channels of differential Step/dir outputs with step r

305.88 €

7I97 Ethernet interfaced Analog servo plus I/O ( See replacement 7I97T)

The 7I97 is a Ethernet connected motion control interface designed for interfacing up to 6 Axis of analog servo motor drives and includes encoder feedback for each axis. The 7I97 has 6 +-10V analog outputs and 6 drive enable outputs. The 7I97 also has 16 isolated inputs plus 6 isolated outputs for g

342.72 €

7I95 Ethernet interfaced Step/dir +encoder + I/O (See replacement 7I95T)

The 7I95 is a Ethernet connected motion control interface designed for controlling up to 6 Axis of step&dir step motor or servo motor drives and includes encoder feedback for each axis. Step rates up to 10 MHz are supported. The 7I95 also has 24 isolated inputs plus 6 isolated outputs for general pu

305.88 €

7I93 Anything I/O Ethernet card

The MESA 7I93 is a low cost, general purpose, FPGA based programmable I/O card with 100 BaseT Ethernet host connection. The 7I93 has a simplified UDP host data transfer system that allows operation in real time if required and compatibility with standard networks for non-real time applications. Firm

109.32 €

7I89 8 Channel encoder 1 channel Serial RS-422/RS-485 interface

The 7I89 is a eight channel encoder plus single channel RS-422/RS-485 interface for Mesa's 25 pin Anything I/O series of FPGA interface cards. The 7I89 is designed for motion control applications. Encoder inputs can be TTL or differential on a per input basis. The 7I89 can also supply 5V power to en

109.32 €

7I98 Anything I/O Ethernet card 3x 26 pin header

The MESA 7I98 is a low cost, general purpose, FPGA based programmable I/O card intended for motion control appications and with a 100 BaseT Ethernet host connection. The 7I98 that uses standard parallel port pinouts and connectors for compatibility with most parallel port interfaced motion control /

121.62 €

7C81 RPI FPGA board

The MESA 7C81 is FPGA motherboard host for a Raspberry Pi CPU. The 7C81 connects to the RPI's GPIO interface and uses SPI for FPGA communication. Three 26 pin header connectors with s tandard parallel port pinouts and 5V tolerant I/O are provided for compatibility with most parallel port interfaced

109.32 €

THCAD-5 High isolation A-D accessory (See replacement THCAD2)

The THCAD is a frequency to voltage converter type A-D designed for high noise environments like plasma voltage monitoring for torch height controls. The THCAD is available in three voltage ranges, 0-5V, 0-10V and 0-300V. When used for plasma voltage monitoring, the 5V and 10V versions require an ex

84.76 €

7I94 Anything I/O Ethernet card (Go to replacement: 7I94T)

The 7I94 is a Ethernet connected motion control interface designed for interfacing up to eight high speed RS-422 or RS-485 serial devices including Mesa sserial remote interfaces, absolute encoders and general serial interfacing. In addition, a FPGA expansion connector compatible with Mesa's 25 pin

146.18 €

7I76ED STEP/IO Step & dir plus I/O daughtercard - sinking output version (Obsolete, see replacement 7I76EU

The 7I76ED ia a remote FPGA card with Ethernet interface designed for interfacing up to 5 Axis of step &dir step motor or servo motor drives and also provides a spindle encoder interface, isolated analog spindle speed control and 48 isolated I/O points for general purpose field I/O use. All step and

244.45 €

7I49HV 6 channel resolver interface

The 7I49HV is a 6 channel resolver interface with 6 additional +-10V analog outputs. The 7I49 is intended for applications that read standalone resolvers, as the 7I49 generates the resolver reference excitation. The 7I49HV can be used with 1:1 and 1:2 transformation ratio resolvers. The 7I49HV has a

226.03 €

7I34-LVDS Eight Channel LVDS interface

The 7I34-LVDS is a 8 channel LVDS interface for Mesa's Anything I/O series of FPGA interface cards. The 7I34-LVDS has 8 independent receive and transmit channels. Each transmit channel has a independent drive enable for bus or 2 wire half duplex systems. The controller connection is a 50 pin header

72.48 €

7I54 Hex 100 Watt H-bridges for Mesa 50 pin I/O FPGA cards

The 7I54 is a low cost 6 Axis H-bridge card for use with Mesa motion control cards. The 7I54 has a maximum per axis current rating of 3 Amps and a voltage rating of 40V. Current limits of 1 Amp and 3 Amp are user selectable, as are voltage and current (torque) modes. All motor power circuitry is gal

207.61 €