Přejít na obsah
  1. Produkty ...
  2. Mesa Electronics
  3. Show All LinuxCNC Supported Boards
  4. Motion Control Cards

Motion Control Cards

Řadit podle Řadit podle: Doporučené
[7I54] 7I54 Hex 100 Watt H-bridges for Mesa 50 pin I/O FPGA cards
7I54 Hex 100 Watt H-bridges for Mesa 50 pin I/O FPGA cards
The 7I54 is a low cost 6 Axis H-bridge card for use with Mesa motion control cards. The 7I54 has a maximum per axis current rating of 3 Amps and a voltage rating of 40V. Current limits of 1 Amp and 3 Amp are user selectable, as are voltage and current (torque) modes. All motor power circuitry is gal
207,61 €
[8I20] 8I20 2200W 3 Phase Amplifier
8I20 2200W 3 Phase Amplifier
The 8I20 is a low cost 2200W 400V three phase torque mode amplifier for synchronous permanent magnet servo motors (Brushless AC servo) up to approximately 3HP. The 8I20 will supply peak currents of 30A. High side logic and gate power are derived from the low side allowing a wide operational bus volt
293,59 €
[7I40-HV] 7I40-HV Dual 400W driver
7I40-HV Dual 400W driver
The 7I40 is a Dual H bridge driver for two brush type motors or other inductive loads. The 7I40 is available in low voltage and high voltage models (7I40-LV and 7I40-HV). The 7I40-LV is rated at 10A 40 VDC per axis while the 7I40-HV is rated at 7A 80 VDC per axis. Each bridge on the 7I40 has selecta
183,02 €
[7I40-LV] 7I40-LV Dual 400W driver
7I40-LV Dual 400W driver
The 7I40 is a Dual H bridge driver for two brush type motors or other inductive loads. The 7I40 is available in low voltage and high voltage models (7I40-LV and 7I40-HV). The 7I40-LV is rated at 10A 40 VDC per axis while the 7I40-HV is rated at 7A 80 VDC per axis. Each bridge on the 7I40 has selecta
183,02 €
[7I39-HV] 7I39-HV Dual 250W 3 Phase BLDC driver
7I39-HV Dual 250W 3 Phase BLDC driver
The 7I39 is a Dual 3 Phase bridge driver for Brushless 3 phase motors. The 7I39 is available in low voltage and high voltage models. The low voltage model is rated at 10A 30 VDC per axis while the high voltage model is rated at 5A 50 VDC per axis. Each 3 Phase bridge on the 7I39 has selectable overc
183,02 €
[7I39-LV] 7I39-LV Dual 250W 3 Phase BLDC driver
7I39-LV Dual 250W 3 Phase BLDC driver
The 7I39 is a Dual 3 Phase bridge driver for Brushless 3 phase motors. The 7I39 is available in low voltage and high voltage models. The low voltage model is rated at 10A 30 VDC per axis while the high voltage model is rated at 5A 50 VDC per axis. Each 3 Phase bridge on the 7I39 has selectable overc
183,02 €
[7I30-4] 7I30-4 Quad 100 Watt H-bridges for 4I27,4I34,4I65,5I20,7I60
7I30-4 Quad 100 Watt H-bridges for 4I27,4I34,4I65,5I20,7I60
The 7I30-4 is a 3A, 36V 4 channel H-bridge motor driver for the 4I27, 4I34, 4I65, 5I20 and 7I60 motion controllers. They use high efficiency synchronous rectifying drivers, eliminating the need for heat sinks. They connect to the motion controller card with a 50 conductor flat cable and have AMP Min
109,32 €
[7I29] 7I29 Dual 2KW H-bridge for 4I27 and FPGA cards
7I29 Dual 2KW H-bridge for 4I27 and FPGA cards
The 7I29 is 2 channel H-bridge motor drivers for the 4I27 or FPGA based motor controller cards. The 7I29 connects to the motor controller card with a 50 conductor flat cable and have screw terminals for motor power and motor connections. Two 7I29's can share a 4 Axis 50 conductor cable to FPGA contr
367,30 €