Mesa Electronics

This common block is for convenient removable screw terminal plug commoning of power and ground connections. The common block uses standard spacing that matches most other Mesa daughter cards. 24 terminals are provided with each common blocksplit into 2 groups of 12 commoned pins. 3.5 mm pluggable s

DIN rail mounting hardware is ava ilable for all daughtercards with 3.7" hole spacing (this inc ludes almost all daughter cards except the 7I73). Hardware consists of a DIN rail clip and aluminum mounting bar plus M3 threaded spacers and screws. Sold in sets of 3.0. 1 set (3 pieces) is suggested for

DIN rail mounting hardware is ava ilable for all daughtercards with 3.7" hole spacing (this inc ludes almost all daughter cards except the 7I73). Hardware consists of a plastic DIN rail clip and aluminum mounting bar plus M3 threaded spacers and screws. Sold in sets of 2. 1 set (2 pieces) is suggest

The 4I70 is a PCI to PCI Express or PCI express to PCI bridge on a PC/104-PCI card. Two 4I70 cards and a single lane Infiniband cable make complete remote PCI bridge system for the PC/104-PLUS bus. The 4I70 allows remote expansion of PC/104-PCI systems and solving problems with PC/104-PCI card stack

The MESA 4I34 is a general purpose programmable I/O card for the PC/104 bus. The 4I34 uses a 100K or 200K gate Xilinx FPGA for all logic, so it is truly an Anything I/O card. The FPGA is downloadable from the PC/104 bus side, allowing creation of almost any kind of specialized I/O function, includin

The MESA 4I34 is a general purpose programmable I/O card for the PC/104 bus. The 4I34 uses a 100K or 200K gate Xilinx FPGA for all logic, so it is truly an Anything I/O card. The FPGA is downloadable from the PC/104 bus side, allowing creation of almost any kind of specialized I/O function, includin

7I78-6I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

7I77U-6I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

7I78-5I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

The CFADPTHD adapter allow use of 2 Compact flash memory cards with any CPU with a 44 pin 2mm or 40 pin .1" IDE connector. The CFADPTHD has 2 CF sockets, one connected as master and one connected as slave. Master and slave can be swapped with a on card jumper. The adapter has an activity light and a

The CFADPT10 adapters allow use of Compact flash memory cards with any CPU SATA connector. The CFADPT10 is in a SATA 2.5" hard drive mechanical format including SATA type power connector. T he adapters have an activity light and a push button ejector, making it suitable for panel mounting. The adapt

The CFADPT9 adapters allow use of Compact flash memory cards with any CPU SATA connector. The adapters have an activity light and a push button ejector, making it suitable for panel mounting. The adapter supports CF cards and Micro-Drives with interface standards up to UltraDMA 150. The on card auxi

The CFADPT7-S can be mounted where a 2.5" hard drive would fit as it has the same mounting holes and same physical size. The CFADPT7 is available as a standard single drive or optionally a dual drive with two CF sockets. The CFADPT7 supports newer CF cards that use DMA. The adapters have an activity

The SPINx1 is a one channel isolated digital potentiometer intended for spindle control. The SPINx1 takes three TTL level signals, PWM, DIR and ENA and has four isolated outputs: CW, CCW, ENA and VOUT. VOUT is a Analog voltage proportional to the PWM input signal and the Analog reference voltage (5

Allows use of standard PCI cards with PC104-PLUS CPU.

T he 4I72 is an adapter that allows use of 4 MINI-PCI type III cards (such as wireless network cards) on a PC/104-PCI host CPU. The 4I72 uses a PCI bridge so that the 4I72 only occupies a single PC/104-PCI slot. The bridge also allows the 4I72 to be used with 5V PCI bus devices since it isolates the

T he 4I67 is an adapter that allows use of 2 MINI-PCI type III cards (such as wireless network cards) on a PC/104-PLUS host CPU. The 4I67 uses a PCI bridge so that the 4I67 only occupies a single PC/104 slot. The bridge also allows the 4I67 to be used with 5V PCI bus devices since it isolates the MI

T he 4I67 is an adapter that allows use of 2 MINI-PCI type III cards (such as wireless network cards) on a PC/104-PLUS host CPU. The 4I67 uses a PCI bridge so that the 4I67 only occupies a single PC/104 slot. The bridge also allows the 4I67 to be used with 5V PCI bus devices since it isolates the MI

T he 4I64 is an adapter that allows use of MINI-PCI type III cards (such as wireless network cards) on a PC/104-PLUS host CPU. The 4I64 can be jumpered for slot 0,1,2 or 3 of the host PC/104PLUS bus. The 4I64 has a local 3.3V regulator for the MINI-PCI card. Local status LEDS are provided and a conn

T he 4I64 is an adapter that allows use of MINI-PCI type III cards (such as wireless network cards) on a PC/104-PLUS host CPU. The 4I64 can be jumpered for slot 0,1,2 or 3 of the host PC/104PLUS bus. The 4I64 has a local 3.3V regulator for the MINI-PCI card. Local status LEDS are provided and a conn

The 485x1 is a single channel TTL to RS422 or RS485 adapter. It supports full duplex (4 wire) RS-422 interfaces or half duplex (2 wire) RS-485 type interfaces.