Mesa Electronics

The MESA 5I24 is a low cost, general purpose, FPGA based progr ammable I/O card for the PCI bus. The 5I24 is a low profile PCI card (available with low profile and standard brackets, standard profile b r acket shown here) Dual FPGA configuration EEPROMs allow simple recovery from programming mistake

The MESA 5I24 is a low cost, general purpose, FPGA based progr ammable I/O card for the PCI bus. The 5I24 is a low profile PCI card (available with low profile and standard brackets, standard profile b r acket shown here) Dual FPGA configuration EEPROMs allow simple recovery from programming mistake

7I85-6I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

7I85-5I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT) OBSOLETE: See 7I85T-5I25 PLUG-N-GO KIT

7I85S-6I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT)

PCI Express, Board to Board Connector, Receptacle, 200 contact, .5mm receptacle verticle, Straight SMT for the 6I68 or 7I68.

RS232 to quad RS422 interfaces on RJ45. For 3C20, 8I20.

The MESA 7I90HD is a very low cost, general purpose, FPGA based progr ammable I/O card with a EPP parallel, RS-422 serial or SPI host interface. Dual FPGA configuration EEPROMs allow simple recovery from programming mistakes. Firmware modules are provided for hardware step generation, quadrature enc

The 7I76E ia a remote FPGA card with Ethernet interface designed for interfacing up to 5 Axis of step &dir step motor or servo motor drives and also provides a spindle encoder interface, isolated analog spindle speed control and 48 isolated I/O points for general purpose field I/O use. All step and

The ENC422 is a one channel (A+B+I) TTL to differential level encoder interface. The 422ENC has three TTL inputs and three differential RS422 outputs. Status LEDs are provided for A,B,I and power.

The 422ENC is a one channel (A+B+I) differential to TTL level encoder interface. The 422ENC has three terminated RS-422 inputs and three TTL outputs. Status LEDs are provided for A,B,I and power.

The 7I77ISOL is galvanic isolation card that electrically isolates and rebuffers signals from the FPGA controller card. The 7I77ISOL is useful in cases where sev ere electrical noise or ground loop problems exist or where longer cable runs are used between the FPGA card and the 7I77.

The HD-DB is an adapter that allows the use of 25 pin daughterc ards with 50 pin FPGA cards. For example the HD-DB will allow the use of a 7I77 with a 5I20, 5I22, or 5I23 etc FPGA card. The 7 unused FPGA I/O pins are brought out to a terminal block for easy access.

7I85S-5I25 PLUG-N-GO KIT - (FOR DIN RAIL MOUNTING, ADD DIN RAIL ADAPTER KIT) OBSOLETE: See 7I85S-5I25T PLUG-N-GO KIT

BRACKET - LP (LOW PROFILE) FOR 5I25 OR 6I25

BRACKETS - SP (STANDARD PROFILE) FOR 5I25 OR 6I25

The PCIEEX is a one lane PCI Express cable extender. It can be used for cable length extention and through panel applications. The PCIEEXR does not swap the XMIT and RECV pairs so can be used in situations with 2 extenders and 3 cables. .

The PCIEEX is a one lane PCI Express cable extender. It can be used for cable length extention and through panel applications. The PCIEEXS swaps the XMIT and RECV pair so must be used in situations with 2 cables and 1 extender.

26 conductor flat cable for EPP use with 7I43,7I61 IDC26 female header to DB25M 3 FT. Can also be used for 5I25,6I25,7I92,7I94,7I95,7I96,7i97,7I98,7C80,7C81 parallel expansion port to daughterboard connections

RS-232 to RS485 adaptor for 4I23 / 4C24 / 4I26/ Generic. RS232, Uses RTS for 485 xmit enable.

CAT5E cable for SSERIAL 4M one end TB8 for 7I52,7I53,7I77.